感應門可以說是我們比較常見的一種門了，在日常的使用中，讓我們的出行變得更加智能更加便捷，解放雙手，輕松出行。濟南感應門廠家提醒您，要預防感應門時常會存在的9個問題!

The induction door can be said to be a common door. In daily use, it makes our travel more intelligent and convenient, hands free and easy. Jinan sensor door manufacturer reminds you to prevent 9 problems that often exist in sensor door!

1、電源不通，沒有送電

1. No power supply

方法：重新送電。

Solution: Re power on.

2、處在鎖門或常開

2. At the locked door or normally open

方法：將按到自動狀態。

Solution: Press to automatic status.

3、存在斷線

3. There is disconnection

方法：檢查排除感應器、電控器、電機、光線，存疑的接線

Solution: check and eliminate the inductor, electric controller, motor, safety light and questionable wiring

4、光線失靈

4. Safety light failure

方法：解除光線接線，門就能正常運行，更新光線或電控器，同時排除其它存疑問題的部件。

Solution: Remove the safety light wiring, the door can operate normally, update the safety light or electric controller, and eliminate other parts with suspected problems.

5、感應器失靈

5. Sensor failure

方法：解除感應接線，按下“測試鍵”門都能正常運行后，同時排除其它存疑問題的部件后，更新電控器。

Solution: Remove the inductive wiring, press the "test key" and the door can operate normally. At the same time, update the electric controller after eliminating other components with problems.

6、電控器失靈

6. Electric controller failure

方法：解除感應接線，多次按下“測試鍵”門都不能正常運行后，檢查相接電機的線。同時排除其它存疑問題的部件后，更新電控器。

Solution: Remove the induction wiring, and check the line connected to the motor after the door can not operate normally after pressing the "test key" for many times. At the same time, update the electronic controller after eliminating other components with problems.

7、電機失靈

7. Motor failure

方法：解除感應接線，多次按下“測試鍵”門都不能正常運行后，檢查相接電機的線。更新電機，同時排除其它存疑問題的部件后。

Solution: Remove the induction wiring, and check the line connected to the motor after the door can not operate normally after pressing the "test key" for many times. After the motor is renewed and other suspected parts are eliminated.

8、由于外接其他門禁設備，發出錯誤信號

8. Error signal is sent due to external connection of other access control equipment

方法：解除門禁接線，多次按下“測試鍵”，門正常運行時，要檢修或更新聯接的門禁設備。

Solution: Remove the access control wiring, press the "test key" for many times, and when the door is in normal operation, repair or update the connected access control equipment.

9、門體卡住

9. The door body is stuck

方法：檢查門體結構變形情況，檢查損壞承重部件情況，重新加固或更新部件。

Solution: check the deformation of the door structure, check the damage to the load-bearing parts, and re reinforce or renew the parts.

感應門機柜內要保持干凈，以防雜質、塵埃損害路軌及動滑輪，危害金屬件的使用期。另外須技術工作人員清潔路軌上的浮灰，增多自動感應門的使用期及降低噪音。關注我們http://www.9pop.cn，了解更多！

The inside of the induction door cabinet shall be kept clean to prevent impurities and dust from damaging the track and moving pulley and endangering the service life of the metal parts. In addition, the technical staff shall clean the floating ash on the track, increase the service life of the automatic sensing door and reduce the noise. Follow us http://www.9pop.cn , learn more!